Ritron RQA-450 Owner's Manual download pdf (Page 10)

qtm9322b.pm5

For assistance, call RITRON at 800-USA-1-USA (800-872-1872) or visit us at www.ritron.com

 8 

C. TO PROGRAM THE ASSISTANCE NEEDED MESSAGE:

1. Pick up the telephone receiver and listen for the

acknowledge tone.

2. Dial 312. Quick Assist II responds with three short

tones to prompt you to begin speaking, then records

the message. This message is to be no longer than 8

seconds. Remember: speak loudly and clearly.

EXAMPLE: Customer needs assistance in Aisle 9.

3. When you have finished speaking, press and release

the telephone flash-hook.

4. You may either continue programming additional

features, or you may dial 999 and hang up the

telephone to stop programming.

NOTE: To review your recorded message,

dial "412".

D. TO PROGRAM TIME BETWEEN REPEATED MESSAGES:

(DEFAULT SETTING IS 30 SECONDS)

1. Look up the code for the desired time between

messages on Table 4, below.

2. Pick up the telephone receiver and listen for the

acknowledge tone.

3. Dial 512, then the code digit from Table 4.

EXAMPLE: If you select 2 minutes as the time between

messages, dial 5124.

4. Quick Assist II responds with a single beep to indicate

it has programmed the time between messages.

5. You may either continue programming additional

features, or you may dial 999 and hang up the

telephone to stop programming.

E. TO PROGRAM A "UNIQUE" LOW BATTERY MESSAGE:

1. Pick up the telephone receiver and listen for the

acknowledge tone.

2. Dial "35". Quick Assist II responds with three short

tones to prompt you to begin speaking, then records

the message. This message is to be no longer than

1.5 seconds.

EXAMPLE: "Low battery Aisle 9"

3. When you have finished speaking, press and release

the telephone flash-hook.

4. You may either continue programming additional

features, or you may dial 999 and hang up the

telephone to stop programming.

NOTE: To review your recorded message,

dial "45".

! ! ! IMPORTANT ! ! !

If your Quick Assist II unit fails to operate

correctly, or is programmed incorrectly, put

the unit into default Quick Assist II mode using

the following procedure:

1. Pick up the telephone receiver and listen for the

acknowledge tone.

2. Dial the correct option (A or B as indicated below),

to restore factory defaults; a short beep indicates

successful completion.

A. For RQA-150, dial 978.

B. For RQA-450, dial 979.

3. Dial 814 to put the unit into Quick Assist II mode;

a short beep indicates successful completion.

4. Dial "5110" to complete the setting of Quick

Assist II mode, a short beep indicates successful

completion

5. Program Sections A through F, above.

6. Programming of the Ritron Quick Assist II is

complete!

F. TO PROGRAM THE "ASSISTANCE NEEDED" MESSAGE

REPEAT LIMIT: (DEFAULT SETTING IS 2 TIMES)

1. Look up the code for the desired number of message

repeats on Table 5, below.

2. Pick up the telephone receiver and listen for the

acknowledge tone.

3. Dial "612", then the code digit from Table 5.

EXAMPLE: If you select 3 times as the message repeat limit,

dial 6123.

4. Quick Assist II responds with a single beep to indicate

it has programmed the message repeat limit.

5. Dial 999 and hang up the telephone to stop

programming.

TABLE 5:

MESSAGE

REPEAT LIMIT CODE NUMBER

1 time ....................................................... 1

2 times ..................................................... 2

3 times ..................................................... 3

4 times ..................................................... 4

5 times ..................................................... 5

6 times ..................................................... 6

7 times ..................................................... 7

8 times ..................................................... 8

Repeat forever; no limit ............................. 9

 DEFAULT

(Programming Instructions continued from page 6)

TABLE 4:

TIME BETWEEN

MESSAGES CODE NUMBER

No Message ............................................. 0

On Changes Only ..................................... 1

30 seconds .............................................. 2

1 minute ................................................... 3

2 minutes ................................................. 4

5 minutes ................................................. 5

10 minutes ............................................... 6

30 minutes ............................................... 7

1 hour ...................................................... 8

2 hours .................................................... 9

 DEFAULT

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Ritron RQA-450 Owner's Manual Page 10

Comments to this Manuals

Related products and manuals for Camera accessories Ritron RQA-450