Ritron Quick Talk Owner's Manual download pdf (Page 8)

qtm9322b.pm5

For assistance, call RITRON at 800-872-1872, or go to www.ritron.comPage 6

PROGRAMMING DIGITAL QUIET CALL SUB-AUDIBLE CODED SQUELCH

INTERFERENCE ELIMINATOR

What is Digital Quiet Call? Digital Quiet Call (DQC) is a

digital sub-audible coded squelch system.

Do I need to program my Quick Talk with a Digital Quiet

Call code? If your radio system does not use Digital Quiet

Call, or any other tradename equivalent, skip this section

and go to the next programming feature.

TO PROGRAM A DIGITAL QUIET CALL CODE:

a. Determine the specific Digital Quiet Call (DQC) code

used for your system, then make sure this code is

listed in Table 3, which shows all of the possible

DQC codes for Quick Talk. If your system code is

not listed, call your radio service provider or Ritron.

b. Write down your code.

c. Pick up the telephone receiver, and listen for the

acknowledge tone.

d. Dial "22" followed by the selected 3-digit DQC code.

For example if your DQC code is "131", dial

"22-131".

Wait for the Quick Talk Confirmation Beep.

e. You may either hang up or continue programming.

TABLE 3: DIGITAL QUIET CALL CODES

TEST YOUR QUICK TALK

WIRELESS VOICE ALARM REPORTER

Normal Invert

023 047

025 ........ 244

026 ........ 464

031 ........ 627

032 ........ 051

043 ........ 445

047 ........ 023

051 ........ 032

054 ........ 413

065 ........ 271

071 ........ 306

072 ........ 245

073 ........ 506

074 ........ 174

114 ........ 712

115 ........ 152

116 ........ 754

125 ........ 365

131 ........ 364

132 ........ 546

134 ........ 223

143 ........ 412

152 ........ 115

155 ........ 731

156 ........ 265

162 ........ 503

165 ........ 251

172 ........ 036

Normal Invert

174 ........ 074

205 ........ 263

223 ........ 134

226 ........ 411

243 ........ 351

244 ........ 025

245 ........ 072

251 ........ 165

261 ........ 732

263 ........ 205

265 ........ 156

271 ........ 065

306 ........ 071

311 ........ 664

315 ........ 423

331 ........ 465

343 ........ 532

346 ........ 612

351 ........ 243

364 ........ 131

365 ........ 125

371 ........ 734

411 ........ 226

412 ........ 143

413 ........ 054

423 ........ 315

431 ........ 723

432 ........ 516

Normal Invert

445 ........ 043

464 ........ 026

465 ........ 331

466 ........ 662

503 ........ 162

506 ........ 073

516 ........ 432

532 ........ 343

546 ........ 132

565 ........ 103

606 ........ 631

612 ........ 346

624 ........ 632

627 ........ 031

631 ........ 606

632 ........ 624

654 ........ 743

662 ........ 466

664 ........ 311

703 ........ 565

712 ........ 114

723 ........ 431

731 ........ 155

732 ........ 261

734 ........ 371

743 ........ 654

754 ........ 116

What is the purpose of testing the Quick Talk radio transmitter?

After following the previous instructions, your Quick Talk will be

programmed to transmit on the same frequency as your radio

receivers, and you also will have programmed your Quick Talk to

transmit any coded squelch signals required for your radio

system.

Do I need to test my Quick Talk Transmitter? Yes; performing

this test now will save you time and confusion later.

TO TEST THE QUICK TALK RADIO TRANSMITTER:

a. Attach the Quick Talk flexible antenna.

b. Turn on your radio receiver.

c. Momentarily place a screwdriver, paper clip or other

electrically conductive item across the Switch #1 terminals.

d. Quick Talk transmits the Closed and Open Switch mes-

sages, which you should be able to hear on your radio

receiver.

If you do not hear the messages, you have probably not

properly programmed the Quick Talk transmitter frequency

or the Quiet Call Coded Squelch. In this case, repeat the

programming, then perform this test again.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Comments to this Manuals

No comments

Ritron Quick Talk Owner's Manual Page 8

Comments to this Manuals

Related products and manuals for Car video systems Ritron Quick Talk